One-Stop Partner for Premium Ceramic Mugs & Tableware

Home / All / Expert Knowledge / The Lot Passed: What a Passing Inspection Says About the Next One

The Lot Passed: What a Passing Inspection Says About the Next One

Nov 15,2026

A buyer's inspector opens the first container, pulls eighty pieces, finds three with a glaze speck on the rim, and the lot passes. Six weeks later the same order arrives from the same factory against the same specification, and the problem is somewhere else: the handles sit low enough that the chain's trays no longer stack in the dish room. Nothing in the first report was wrong. Nothing in it was about the second delivery either.

Products in this guide: Ceramic Baking Bowl · White Ceramic Dessert Plate

An inspection report records what a defined sample looked like on a defined day. That answers the question that matters at the dock: ship this, or reject it. The question it cannot answer is whether the next container will behave like this one, which is the question that decides whether a supply relationship holds up over a year.

Between those two questions sits everything that moves in a ceramic plant, week to week and load to load.

See the full ceramic sourcing process map.

A Pass Is a Threshold, Not a Description

Acceptance sampling compares a sample against a limit and returns a decision. The decision is binary, which is why it travels so well: it fits on a report, in an email, in a container release. It also discards how close the pieces sat to that limit, and which way they were leaning.

Two factories can pass every lot for a year from different positions: one runs a tight process centred on target, the other a wide process that happens to sit inside generous limits. Buyers who see only the decision cannot tell them apart, and the difference surfaces later as fit problems between components bought at different times.

Where the Variation Actually Lives

Most movement in a fired ceramic part comes from a handful of places, none of which appear in a final inspection:

  • Body: a new clay batch changes shrinkage, and shrinkage moves every fired dimension at once.
  • Glaze: slurry density and application weight shift the fired surface, and a gram or two per piece changes how a colour reads.
  • Kiln: position within the load matters, because the top of a stack does not see the same heat history as the bottom.
  • Mould: wear is monotonic, so a mould at the end of its life releases a piece slightly larger than its first week produced.
  • Decoration: registration is set against a body that will shrink afterwards, so a body change moves the print with it.
  • People: two shifts can set the same machine differently and both believe they followed the card.

Yield and Capability Are Two Different Numbers

Yield is the share of measured pieces inside the limits. Capability is the distance from the process average to the nearest limit, expressed in units of the process spread. The first describes a lot; the second describes the process that made it.

A height specification with a two millimetre window can be met at ninety-eight per cent by a wide, off-centre process that would fail the same target on a one millimetre window. Same yield, different process.

This is why widening a tolerance is not an improvement. Yield rises, the report looks better, and the variation is untouched. It reappears as stacking height, lid fit, capacity complaints or a tray that no longer nests, none of which trace back to the clause that was relaxed.

What a Control Chart Shows That a Report Cannot

A control chart plots one measurement in the order it was taken, lot after lot, against a centre line and limits derived from the process's own variation. Three things become visible that a single report flattens: a trend, usually wear or slurry drift; a step, usually a material change or a new operator; and runs of points on one side of the centre, which mean the process settled somewhere other than where it was set.

The chart also separates two kinds of cause. Common cause is the ordinary spread of a stable process, and only a change in the process reduces it. Special cause is a one-off event that pushed the process off its pattern. Tightening inspection is the usual response to both, and for common cause it is wasted effort, because inspection sorts pieces rather than changing what produced them.

Reading a Capability Figure Honestly

A capability index is a ratio, and a ratio without its conditions is decoration. Four questions turn a number into evidence: which dimension it covers, since a figure for rim diameter says nothing about capacity; over what period, since a good week is not a year; from how many pieces, since a small sample makes any index look confident; and whether the distribution was checked, since several tableware dimensions are skewed and a symmetric index overstates what the process holds.

Most figures fall apart on one question: whether the index used the limit the buyer wrote, because a two-sided window and a one-sided floor are different calculations.

What to Ask For, and What It Costs

The cheapest request uses records the factory already keeps. Routine in-process measurement exists in most plants: height and diameter at the first piece, capacity by filling, glaze weight by weighing before and after. Asking for the last twenty-five readings of two or three key dimensions is close to free, and it already shows whether the numbers are stable or drifting. The spec freeze guide explains how artwork and packing files are locked between orders.

The next step is plotting those readings with a written action rule, so an out-of-limit point triggers a defined response rather than a conversation. Beyond that, a third-party capability study on a running order carries a real cost and belongs where component fit matters more than the study.

Four Lines for the Order File

Documents travel better than intentions, and this compresses into four clauses:

  1. Name the dimensions that matter for fit, each with the method used to measure it, so two people measuring one piece get one number.
  2. State the record: how many pieces per lot, at what frequency, and that the readings accompany the shipment rather than waiting to be requested.
  3. Write the action rule, including who is told and what happens to pieces already made when a point falls outside the limits.
  4. Require notice before any change that moves dimensions: a new clay batch, a new mould, a kiln repair, a change of decoration supplier. The master sample guide explains how sealed references keep batches identical.

None of this makes a bad lot impossible. It changes what is known before the container is loaded, and it replaces the sentence that carries most supply relationships, which is that the last one was fine, with a record of what fine actually meant.

Are you looking for a reliable ceramic tableware manufacturer?

We can quickly provide customers with market analysis, technical support and customized services.


Please send your message to us
*Email
Phone
*Title
*Content
Upload
  • Only supports .rar/.zip/.jpg/.png/.gif/.doc/.xls/.pdf, maximum 20MB.