An Approval Has a Date: What a Sample Sign-Off Covers and How Long It Holds
A sample is approved on a Tuesday in March. Two pieces are sealed, one stays with the buyer and one stays with the factory, and the thread closes with the word approved. Production is scheduled for November, once a retail listing is confirmed and a budget released.
Products in this guide: Gradient Ceramic Mug - Laser Engraved · 290ml Reactive Glaze Ceramic Travel Coffee Mug with Lid
In November nobody asks whether the approval still applies. The file says approved, the factory treats it as the instruction, and the run begins. The unanswered question is the one that decides whether the November ware matches the March piece: has anything happened in eight months that the approval did not cover.
An approval is written as though it were permanent, a property of the design like a drawing or a colour code. What it records is narrower: that one lot, on one set-up, at one time, matched a specification both sides agreed to read the same way.
What a sign-off certifies, and what it does not
The record is about a lot, not a factory. A lot has a date. The set-up that made it has a date too, and the two are not the same.
Between approval and running, the plant keeps working: other orders, new clay, incoming glaze, a plate re-cut, a mould replaced. None of it appears in the approval, which was never built to record it. The document answers a question about one morning and is then read for years as an answer about a capability.
Three clocks, three speeds
The single word approval hides three things, and each ages at its own rate.
- The reference piece. A sealed sample is physical. It collects dust, its label can fall off, and on a matte glaze it picks up handling marks that later read as a surface difference. A reference opened a dozen times is no longer a reference.
- The evidence file. Test reports and colour measurements are dated documents with their own lifetimes. A report from an earlier run describes that run. Reusing it later is a claim about the set-up, not about the ware.
- The authority to approve. Sign-offs belong to people. Buyers change roles, factories change who answers the email, and a signature from someone who has left still binds, and nobody left in the thread remembers what it agreed to.
What ages while nothing is being made
Some parts wear with use, some change untouched, and one fixed validity period fits neither.
A mould cavity wears with every cycle, so its drift tracks volume. A decal plate wears with every print run and fails first in fine type. A body source can shift without the factory doing anything, because clay arrives from a seam that is not identical season to season. Glaze is the least stable: a frit supplier can reformulate, a colourant can be substituted, a cost adjustment can pass unremarked. A packing die is stable until the carton supplier changes.
Why the calendar is the weakest trigger and still worth writing
Every plant has a change-notification habit, and it works exactly as well as the memory of the person running it. Change control catches deliberate changes. It is far weaker at the change nobody classified as one, because a new glaze batch looks like the same glaze from inside the plant.
A date does not depend on anyone recognising a change. It forces a decision at a fixed point: the approval is confirmed against the current set-up, or renewed, or production stops. All three are acceptable. The fourth, where nothing happens because nothing was scheduled, is not.
Renewal before the run is cheap; renewal at pack-out is not
The cost of re-validation is mostly a question of timing, and the curve is steep.
Before the run it means a small trial against the sealed reference, a comparison under agreed light, and a note. One day of factory time and a decision about whether anything moved. At pack-out the same question is asked about finished goods on built pallets, with a vessel booked and a retail date fixed. It is no longer a quality question. It is a negotiation, and the party holding the goods has the weaker position.
Dating an approval is therefore worth more than tightening it. A date creates a decision point while the order is still cheap to change.
Five lines that make a sign-off re-checkable
The record does not need length. It needs to be answerable by someone who was not in the room.
- The date and the lot. When approval was given, and which production or sample lot it refers to. An approval with no lot reference cannot be tied to ware.
- The set-up it certifies. Body source, glaze batch or reference, mould number, decoration plate, packing die. Named rather than described, so a substitution shows up as a substitution.
- The reference holder. Which physical piece is the standard, and where each copy sits. A reference held by one party alone cannot be checked by the other. The master sample guide explains how sealed references keep batches identical.
- The voiding events. What cancels the approval without discussion: a change of body or glaze source, a re-cut mould, a new plate, a new carton die, a new market requirement.
- The review date and who closes it. A named owner on each side and the evidence that counts as closure. A date with no owner is a reminder that gets forwarded until it is ignored.
When the approval has already gone stale
Most approvals in circulation are undated, so the practical question is what to do with one that may no longer describe the current set-up. The answer is rarely to restart the sampling cycle.
Compare current production against the sealed reference under conditions both sides agreed on, then ask the factory to state in writing what has changed since approval. If nothing has, the approval can be re-dated with a note and the order proceeds on a current document. If something has, that item is the scope of the re-approval, which becomes a comparison rather than a new design round. The spec freeze guide explains how artwork and packing files are locked between orders.
The distinction is commercial. A full re-sample invites a re-quote and a fresh argument about specification. A scoped re-validation confirms what did not move and examines what did, which is usually one glaze batch.
Approvals accumulate the way files do, and the ones that still mean something were written to be checked later rather than admired once. Dating one costs a line and changes what happens when something goes wrong. An undated approval leaves both sides arguing about what was agreed. A dated one leaves them looking at the same reference and the same list of changes.
Related Products
Explore products featured in this guide:
Have questions? See our Sizes & Finishes FAQ and Ordering & Certifications FAQ.
Need a custom quote? Send an inquiry or browse our full product catalog.









